Products
"Bullshit" Lapel / Hat / Jacket Enamel Pin
$6.00 USD
Seems appropriate. This Classy lookin' Bullshit pin says it better than I ever could. Great Gift! We love selling pins at shows!
"TRY IT, YOU'LL LIKE IT - MR BUS CO" Giant 4.5x14" Sticker
$4.50 USD
HUGE STICKER! 4.5x14" outdoor UV Vinyl bumper sticker. peel n stick anywhere and everywhere.
"Very High" Patch
$5.00 USD
What is the fire danger near you? Its Very High! Let people know by wearing the warning, "VERY HIGH" Patch. Iron on or Sew on or BOTH!!! A MrBusCo Brand product!
009 / 034 Tune Up Kit - BOSCH Cap, Bosch Points, Beru Rotor
$32.00 USD
– Sold OutReplacement Cap, Rotor, and Points for 009 and 034 Distributors.
1.5" Exhaust J Tubes, Pair
$42.00 USD
Don't drive your type 1 powered VW in the colder months? Maybe you're tired of reaching around your heater boxes every time you pull your motor? These install in place...
10mm oil cooler seals
$4.00 USD
10mm / 10mm oil cooler seals for Type 1 upright engines 1970 and up. 4 required on 71 and later engines. We have found these black seals to be...
10mm Type 3 oil cooler seals - PAIR
$4.00 USD
While these seals appear the same as a standard oil cooler seal, you will notice that is thicker in the middle, and is used for type 3 engines only. It...
12v + 6v Gen / Alt Pulley Spanner Set BB-237
$30.00 USD
For use on the small 6v 99mm and larger 12v 108mm Generator/Alternator top pulley Holds top pulley in place while undoing the 21mm nut that holds the pulley halves together. ...
16 AMP Red Fuse (PACK OF 5)
$4.00 USD
25 amp fuse, white. N171215 Pack of 5
21mm Oil Pump 8mm holes - Flat Cam - Schadek
$39.00 USD
Schadek 21mm Oil Pump for cases with 8mm studs and a flat (3 bolt) cam. This is the stock size pump and absolutely adequate for your stock engine. correct for 1970-1971 model engine...
25 AMP Blue Fuse (PACK OF 5)
$4.00 USD
25 amp fuse, white. N171215 Pack of 5
26mm Oil Pump 6mm holes - Flat Cam - Schadek
$39.00 USD
Schadek 26mm Oil Pump for cases with 6mm studs and a flat (3 bolt) cam. Fits 13-1500cc engines with 6mm studs. Will fit all earliery engines 25, 36, 40hp with slight...
26mm Oil Pump 8mm holes - Dished Cam - China
$25.00 USD
26mm Oil Pump for cases with 8mm studs and a Dished (4 bolt) cam. Correct for 1971 and up type 1 engine cases with 8mm studs. This is an affordable Chinese...
26mm Oil Pump 8mm holes - Dished Cam - Schadek
$39.00 USD
– Sold OutSchadek 26mm Oil Pump for cases with 8mm studs and a Dished (4 bolt) cam. Schadek Brand PumpFits Dished Cams 71-7926mm Gears8mm Bolt HolesCam Type: DishedGear Size: 26mmBeetle Type 1:...
26mm Oil Pump 8mm holes - Dished Cam - SMIDTD
$25.00 USD
– Sold Out26mm Oil Pump for cases with 8mm studs and a Dished (4 bolt) cam. Correct for 1971 and up type 1 engine cases with 8mm studs. This is an affordable Mexico made...
26mm Oil Pump 8mm holes - Flat Cam - Schadek
$39.00 USD
Schadek 26mm Oil Pump for cases with 8mm studs and a flat (3 bolt) cam. Correct for 66-69 engine cases with 8mm studs. OEM Number 311-115-107AHD
30mm Oil Pump 8mm holes - Dished Cam - Schadek
$39.00 USD
Schadek 30mm Oil Pump for cases with 8mm studs and a dished (4 bolt) cam. We only go to a 30mm pump if adding an external oil filter and cooler, or...
30mm Oil Pump 8mm holes - Flat Cam - Schadek
$39.00 USD
Schadek 30mm Oil Pump for cases with 8mm studs and a flat (3 bolt) cam. We only go to a 30mm pump if adding an external oil filter and cooler, or...
34 Pict 3 Carburetor - Mr Bus Co
$90.00 USD
This is our stock 34 PICT 3 carb, 12v choke. These are just fantastic carbs. They just work! These are white box chinese carbs. We go over each carb and...
60 amp Alternator, New
$120.00 USD
Here's a nice upgrade from a generator, our 60 amp alternator. These are 100% brand new! To convert your generator equipped car, you'll need the alternator stand, backing plate kit,...
63-71 Bus Tailpipe
$12.00 USD
– Sold OutEuro made bus tail pipe. Fits 1963-1971 stock buses exhaust.
8 AMP White Fuse (PACK OF 5)
$4.00 USD
8 amp fuse, white. N171211 Pack of 5
8mm/10mm Oil Cooler Adapter Gaskets - PAIR
$2.00 USD
These special gaskets are for installing a late model doghouse style oil cooler on an early style block with the stamped steel oil cooler. The smaller end of this gasket...
AA Cast 85.5mm x 69mm Pistons and Cylinders
$149.00 USD
– Sold OutThis is a new set of standard 85.5mm Type 1 pistons and cylinders. This kit requires no machine work and will slide right in to any 1500 or 1600cc air...
AA Cast 90.5mm x 69mm Pistons and Cylinders
$199.00 USD
– Sold Out90.5mm VW Aircooled Type 1 Pistons and cylinders. This kit does require machine work on the cylinder heads and case; Fits 90.5/92 Case, 90.5/92 Heads. Will work with small stroked cranks 69, 74, and 76 ...
AA Cast 94mm x 69mm Pistons and Cylinders
$199.00 USD
– Sold OutThis is a new set of 94mm VW Aircooled Type 1 Pistons and cylinders. This kit does require machine work on the cylinder heads and case; Fits 94 Case, 94 Heads. Will work...
Air Deflector plate, Left
$16.00 USD
Tin piece that mounts to the left of the crank pulley, under the cylinder tin. Josh's Note: I'm sure this piece fits "something" as is, but I haven't found it. ...
Air Deflector plate, Right
$16.00 USD
Tin piece that mounts to the left of the crank pulley, under the cylinder tin. Josh's Note: I'm sure this piece fits "something" as is, but I haven't found it. ...
Alternator - Generator Woodruff Key Kit
$3.00 USD
These little jerks like to go flying when installing or removing either the fan hub or the pulley, make sure you have extras on hand and save yourself lots of...
Alternator / Generator Stand Gasket
$0.40 USD
This gasket goes between the alternator stand and the engine block. Two are required, one above and below the oil deflector plate. SOLD EACH
Alternator Conversion Tin Kit
$15.00 USD
Upgrading your tired old generator to an alternator? This kit has the required backing tin to make sure your conversion works out! It has the two large backing plate tins...
Alternator or Generator Stand, New
$19.00 USD
This stand is required when switching from generator to alternator, but will also work with any 12 volt generator. Don't forget your new oil fill and gaskets!
Alternator Style Fuel Pump
$26.00 USD
Budget Fuel pump, made in China. For use on 1200-1600 type engines with an Alternator. Uses the "short" 100mm pushrod. Josh's Notes: These pumps work fine and are cheap. ...
Autolinea Dual Port Cylinder Head
$249.00 USD
– Sold OutNEW Stock replacement dual port cylinder heads. Great OE quality heads made in Brazil, with stock valves and springs. Will fit 1300, 1500, 1600, 1641cc engines or 83mm, 85.5mm, 87mm pistons....
BB-013 55-59 T2 LHD Throttle linkage Kit
$75.00 USD
MrBusCo Loves these kits! They should be standard equipment on all buses. This kit will fit Late 1955-1959 models. This kit is an upgrade from the old worn out original...
BB-014 59-67 T2 LHD Throttle linkage Kit
$75.00 USD
– Sold OutMrBusCo Loves these kits! They should be standard equipment on all buses. This kit will fit Late 1959-1967 models. This kit is an upgrade from the old worn out original...
BB-016 Accelerator Pedal Pushrod Boot 55-79 T2
$9.00 USD
This is a VW Genuine floor rubber/boot. Will fit Split screen vans and Bay windows. 1955-1979 Genuine part number is 211721621. SOLD EACH
BB-017 68-71 T2 LHD Throttle linkage Kit EARLY BAY
$75.00 USD
MrBusCo Loves these kits! They should be standard equipment on all buses. Will fit Left hand drive busses from 1967 to 1972 build date (Early Type 1 engine Bay) This...
BB-018 72-79 T2 LHD Throttle linkage Kit LATE BAY - CARBS
$75.00 USD
MrBusCo Loves these kits! They should be standard equipment on all buses. Kit fits Late Bays with type 4 engines and carbs. This kit will be replace the old setup,...
BB-053 Stainless Steel Early Beetle bumper light mounts
$25.00 USD
Early Beetle blade bumper blade light mounts (Will not fit the later style bumpers)Sold in Pairs . (Left hand and Right hand fitment)These are copies of an old Bosch style mount...
BB-066 Rear mudflap mount Early Beetle Blade Bumpers
$55.00 USD
HEAVY DUTY! Stainless steel Blade bumper Mud flap holders, You are buying a pair (a left hand side and right hand side mount). These have been made copying originals from...
BB-088 Rear mudflap mount LATE Bay 72-79
$50.00 USD
HEAVY DUTY! Price is for a pair (left hand and right hand mount) these are designed for the later pancake style engines (Type 4) Made from mild steel then plated black...
BB-103 Throttle Cable Guide Roller Kit 55-67 T2
$27.00 USD
MrBusCo Loves these kits! They should be standard equipment on all buses. This roller just bolts to the gearbox, kit comes with a new M8 nut and locking washer, you...
BB-111 72-79 T2 LHD Throttle linkage Kit LATE BAY - FI
$70.00 USD
MrBusCo Loves these kits! They should be standard equipment on all buses. Kit fits Late Bays with type 4 engines and Fuel Injection. This kit will be replace the old...
BB-130 Rear mudflap mount Splitwindow bus
$50.00 USD
HEAVY DUTY, Splitscreen vw rear mudflaps mount kit, made in steel then zinc and black coated. These are a little thicker than the originals that usually get bent. They are...
BB-142 Rear mudflap mount Early Bay 1968-71
$50.00 USD
HEAVY DUTY, Earlybay T2a Rear mudflap mounting kit , kit is steel and has been plated in Zinc and Black . Kit comes with everything needed for 1 vehicle ,...
BB-154 LHD/RHD Throttle Pedal Stop 68-71 Early Bay
$10.00 USD
Ever wondered why you have 2 holes underneath your throttle/accelerator pedal ? Years ago the holes would have had this pedal stop fitted , but over time people either removed...
BB-170 Westfalia sliding door helper + Black handle Bay Window
$29.00 USD
Bay Window sliding door helper handle kit with black handle. Reproduction of a factory option, the helper handle allows you to more easily close the slider, especially when you have...