Gaskets
Engine Gasket Set, 1300-1600cc (Elring)
$19.50 USD
– Sold OutComplete Engine Gasket Set. Includes all the gaskets and seals for the assembly of the engine. High quality valve cover gaskets are included.
Oil Deflector Plate Alternator / Generator Stand
$1.00 USD
– Sold OutMetal oil deflector plate. between Generator stand and case. paper gasket goes on each side(sold separate) Deflector Plate, Gasket Generator Support, Type 1 60-79, Ghia 60-74, Type 2 63-71, Type...
Dual Port Intake Install Kit Boots Clamps Gaskets BLACK
$11.00 USD
Quality Step-Style Red Boot installation kit. Clamps and quality dual port intake gaskets are included.
Dual Port Intake Install Kit Boots Clamps Gaskets RED
$11.00 USD
Quality Step-Style Red Boot installation kit. Clamps and quality dual port intake gaskets are included.
Oil Relief Plug Gasket
$0.60 USD
This is a crush gasket that goes around the oil relief plug in the case. You'll need to make sure your case is single or dual relief, as that will...
Carburetor Base Gasket - 34 PICT-3
$2.50 USD
This gasket goes between the intake manifold and the carb. This is the larger style for engines using a 34 PICT-3 carb. SOLD EACH
Carburetor Base Gasket - 28 - 30 PICT
$0.50 USD
This is the gasket between the intake manifold and the carburetor. This is specifically for early style 28-30 carbs. There is a larger gasket for 34 PICT 3 carbs.
Single Port Intake Manifold Gasket - Set
$2.00 USD
These crush metal gaskets go between the head and the intake manifold on all 13-1600 single port engines, including Type 3. These are like oil drain plug crush washers, you're...
Dog House Style Oil Cooler Gaskets - FOUR
$4.00 USD
These are great quality gaskets. For an engine with a doghouse cooler, you'll need two pairs, one to go between the oil cooler stand and the block, and another to...
8mm/10mm Oil Cooler Adapter Gaskets - PAIR
$2.00 USD
These special gaskets are for installing a late model doghouse style oil cooler on an early style block with the stamped steel oil cooler. The smaller end of this gasket...
Push Rod Tube Gasket - Full Set
$7.00 USD
This is a full set of high quality pushrod tube seals for any 13-1600 and beyond style engine. Each tube requires a seal at each end, and there are 8...
Exhaust heat riser gasket - PAIR
$2.00 USD
This little gasket goes between the heat risers on your single carb manifold and your muffler/header. SOLD PAIR
VW Oil Change Gasket Kit, 1300-1600 (Seal & Washers), Made in Germany
$1.50 USD
– Sold OutThis is a set of gaskets for your oil drain plate, a must when changing your own oil. These are high quality German gaskets, including a drain plug crush washer...
Oil Pump Plate Gasket
$0.75 USD
This gasket goes between the face of the oil pump and the oil pump cover.
Oil Pump Body Gasket - 8mm studs
$0.75 USD
This gasket goes between the oil pump body and the engine case. Oil Pump Body Gasket (8mm), Each, Type 1 67-79, Ghia 67-74, Type 2 67-71, Type 3 67-73
Alternator / Generator Stand Gasket
$0.40 USD
This gasket goes between the alternator stand and the engine block. Two are required, one above and below the oil deflector plate. SOLD EACH
Dual Port Intake Manifold Gaskets PAIR
$2.50 USD
This gasket goes between the intake manifold and the intake ports. These stamped steel gaskets work just fine for any stock dual port application. Sold as PAIR
Metal Clad Exhaust Flange Gasket - Type 1 Engine
$0.90 USD
These gaskets go between the exhaust ports on the heads and the muffler/heater box/J-tube. We like these metal gaskets best! SOLD EACH
Fuel Pump Base Gasket - BOTTOM
$0.45 USD
Fuel Pump base mounting gasket. Goes in between the bakelite stand and the engine case.
Fuel Pump Base Gasket - TOP
$0.45 USD
Fuel Pump base gasket, for in between the bakelite mounting base and the fuel pump. Use extra gaskets to lower your pressure if necessary.
Premium German Cork Valve Cover Gaskets
$3.50 USD
So many options out there for valve cover gaskets. Here at MrBusCo we use these premium German cork gaskets, installed dry with no sealant, and have great luck with them....
Case Stud Sealing O-rings - Set of 6
$4.00 USD
Large O-rings for the six case half studs. Always use new O-rings when you split the case.
Distributor Shaft Seal O-ring
$1.00 USD
Good reproduction seal. Most aftermarket distributors come with a lackluster seal with a square profile. These have the correct rounded D profile, fit, and seal great. If you have had your...